A shower support bar, also called a stabilizer bar, is a metal tube that ties the top of a fixed glass panel to a wall, the ceiling or another panel so the glass cannot flex. HIPAD makes support bars and their connectors in stainless steel 304: Φ19, Φ22 and Φ25 mm round tube, square tube and flat bars, with glass-to-wall and glass-to-glass connectors at 90°, 135° and 180° for 10–12 mm tempered glass. Distributors, shower enclosure makers and glass processors in 60+ countries buy them factory-direct, standard or custom.
A frameless shower panel is held only at its edges, by Pinzas para vidrio or a U-channel. A tall panel with a free edge can still move at the top, and every time the door closes the panel takes the impact. A support bar fixes that top corner to a solid point, so the panel stays straight and the door keeps its alignment.
A support bar system has three parts: the tube or flat bar, un glass connector that clamps through a hole near the top of the panel, and a wall flange, ceiling fitting or second glass connector at the other end. The bar is also called a stabilizer bar, shower brace, header bar o tie bar, and in Spanish barra estabilizadora, tirante para mampara o barra de tracción para baño.
Representative models from the HIPAD range. Our catalog lists about 30 connector models for round and square tube. Every bar and connector can be made in your finish, length and packaging. Ask for the full catalog with drawings.
Respuesta rápida: add a support bar when a fixed panel is wider than about 1000 mm, has a free vertical edge longer than about 1200 mm, o carries a door on glass-to-glass hinges. Walk-in screens with one free end almost always need one. A panel clamped on two or three sides, under 1000 mm wide, usually does not.
| Situación | Support bar? | Typical bar |
|---|---|---|
| Panel clamped on wall and floor, up to 1000 × 2000 mm | Usually not | — |
| Panel 800–1000 mm wide next to a door | Recommended | Glass-to-wall, 90° |
| Panel wider than 1000 mm | Required | Glass-to-wall or wall-to-wall |
| Walk-in screen with a free end | Required | Glass-to-wall or glass-to-ceiling |
| Door hung on a fixed panel (glass-to-glass hinges) | Required | Glass-to-wall or header bar |
| Corner shower, door on the return panel | Recommended | Elbow or 90° corner bar |
| Panel taller than 2100 mm, or 12 mm glass | Required | Φ25 mm tube |
Send the panel sizes and the distance to the wall or ceiling. We return a bar length, tube size and connector list.
Choose a bar by what it connects: glass to a wall, glass to glass, or glass to the ceiling. The views below show each configuration seen from above, except the ceiling rod, which is shown from the front.
A straight tube from the top of the panel to the back or side wall, with a glass connector at one end and a wall flange at the other. Single-head and double-head versions are available.
Slanted-head, elbow and curved bars reach a wall point that is not square to the panel, or bend around a corner. Swivel connectors take up small angle differences on site.
Short bars and connectors that join a front panel to a return panel at 90°, or two panels to each other. They are used in corner showers where the door hangs on the return panel.
Flat bars and adjustable connectors link inline panels across a door opening (180°) or join the angled panels of a neo-angle shower (135°). They sit close to the glass for a slim look.
Vertical rods run from above down to the top of the panel. They are used for walk-in screens and islands where no side wall is within reach. Confirm the fixing details for your ceiling with us.
Tube clamps, wall flanges, end caps and custom connectors complete the system. We make connectors to your tube size, glass thickness and hole drawing, starting from our existing molds.
| Producto | Shower support bars (stabilizer bars), glass connectors, wall flanges and tube clamps for frameless shower enclosures and glass screens |
|---|---|
| Configurations | Glass-to-wall 90° and angled · glass-to-glass 90°, 135°, 180° · wall-to-wall · glass-to-ceiling |
| Bar types | Straight single-head and double-head, slanted-head, elbow, curved, 90° corner, 135° and 180° flat bars |
| Tube | Round Φ19, Φ22 and Φ25 mm · square tube · flat bar |
| Connector sizes | About 30 × 30 to 70 × 30 mm for standard connectors; larger bodies up to about 115 × 70 mm |
| Grosor del vidrio | 10–12 mm tempered glass; some connectors 6–12 mm |
| Longitud | Made to your layout drawing |
| Materiales | Acero inoxidable 304 |
| Acabados | Mirror polished, satin (brushed), matte black, gold; other plated and PVD colors to match your hinges and clamps |
| Juntas | Rubber or PVC gaskets and sleeves at the glass connector |
| Cantidad mínima de pedido · muestra · plazo de entrega | 1000 unidades · 5-7 días · 20-25 días laborables |
| Condiciones comerciales | FOB Qingdao o cualquier puerto de China · Depósito de 30%, 70% antes del envío · T/T, L/C, Western Union, PayPal · Garantía de 1 año |
| Certificaciones | Gestión de la calidad según la norma ISO 9001; certificaciones CE, GS y CSA C-UL para los productos correspondientes · Posibilidad de inspección por terceros (SGS / BV) |
| Connector | Joins | Angle | Tube | Vidrio | Uso habitual |
|---|---|---|---|---|---|
| Glass-to-wall connector + flange | Panel to wall | 90°, fixed | Φ19 / 22 / 25 mm | 10-12 mm | Standard shower screen |
| Swivel connector | Panel to wall | Ajustable | Tubo redondo | 10-12 mm | Out-of-square walls, angled bars |
| Glass-to-glass bar connector | Panel to panel | 90° / 180° | Tubo redondo | 10-12 mm | Corner and inline enclosures |
| Adjustable glass-to-glass connector | Panel to panel | Ajustable | Short tube | 10-12 mm | Neo-angle and custom angles |
| Flat bar clamp | Panel to panel | 135° / 180° | Flat bar | 10-12 mm | Slim inline and neo-angle screens |
| Square tube connector | Panel to wall or panel | 90° / 180° | Tubo cuadrado | 10-12 mm | Modern square hardware lines |
| Tube clamp | Tube to tube | — | Tubo redondo | — | Joining or supporting long bars |
| Barra de soporte | Extra clamps | U-channel | Full header | |
|---|---|---|---|---|
| What it stops | Top of the panel flexing | Edge movement | Edge movement along the full edge | Top movement of all panels |
| Works on a free edge? | si | No, needs a wall or floor | No, needs a wall or floor | si |
| Look | One slim tube | Minimal | Continuous line | Frame along the top |
| Preparación del vidrio | One hole per connector | Clamp-only or small holes | No drilling | Notches or holes |
| Ideal para | Wide panels, walk-in screens, doors on glass | Panels under 1000 mm | Out-of-square walls | Large enclosures, sliding systems |
A support bar sits at the top of the shower, where steam collects and water does not dry quickly. HIPAD makes support bars and connectors in stainless steel 304, which resists rust in daily bathroom use far better than 201 or plated iron. For coastal, pool and spa projects, ask us about 316 stainless steel.
| Tube size | Look | Uso habitual |
|---|---|---|
| Φ19 mm | Very slim | Short bars, light 8–10 mm panels |
| Φ22 mm | Estándar | Most home and hotel showers |
| Φ25 mm | Strong | Long bars, 12 mm glass, walk-in screens |
| Square / flat | Modern, low profile | Square hardware lines, inline joints |
Support bars are made in the same finishes as our bisagras para ducha, glass clamps and handles, so the bar matches the rest of the enclosure. Other plated and PVD colors are available for private-label collections.
La instalación debe realizarla un cristalero cualificado.
| Problema | Corregir |
|---|---|
| Panel still moves with the bar fitted | Check the wall plugs hold; use a larger tube or move the connector closer to the top corner |
| Bar pulls the panel out of plumb | Measure the bar length after the panel is set; use a swivel or adjustable end |
| Door hits the bar | Move the connector lower or use an angled or elbow bar |
| Connector slips on the glass | Replace worn gaskets; tighten screws evenly |
| Rust spots on the bar | Use 304 stainless; clean with a neutral cleaner, not bleach |
HIPAD is a manufacturer, not a trading middleman. We started in 2000 with bearings and precision motion parts, and in 2020 we added stainless steel handles, glass clamps, shower fittings and railing. Tooling, molds, production, assembly and inspection are all in-house, so support bars and connectors can be built to your drawing, finish and brand.
Incoming materials, in-process parts and finished bars and connectors are inspected by our in-house QC team, including tube size, thread fit and surface finish. SGS or BV third-party inspection is available. HIPAD is ISO 9001 certificados, y los productos correspondientes llevan CE, GS y CSA C-UL Certificación. Los certificados correspondientes a un modelo concreto están disponibles previa solicitud.
| 1. Solicitud de información y planos | Send the layout, bar type, tube size, finish and quantity |
|---|---|
| 2. Muestras | 5 a 7 días |
| 3. Producción | 20-25 días laborables · Cantidad mínima de pedido: 1000 unidades |
| 4. Envío | FOB Qingdao o cualquier puerto de China |
| Término | Significado | También se conoce como |
|---|---|---|
| Barra de soporte | Tube that holds the top of a glass panel | Stabilizer bar, shower brace, tie bar, barra estabilizadora, tirante para mampara |
| Header bar | Bar running across the top of a door opening or enclosure | Top bar, header |
| Glass-to-wall connector | Fitting that clamps the bar to the glass | Glass bracket, bar clamp |
| Wall flange | Round plate that fixes the bar end to the wall | Wall bracket, escutcheon |
| Swivel connector | Connector with an adjustable angle | Adjustable connector, articulated joint |
| Elbow bar | Bar with a 90° bend for corners | Corner bar, tirante de codo |
| Flat bar | Flat strip joining panels at 135° or 180° | Strap connector |
Por lo general, un panel fijado a la pared y al suelo con un ancho inferior a unos 1000 mm no la necesita. Añada una barra de soporte cuando el panel tenga un ancho superior a unos 1000 mm, tenga un borde vertical libre de más de unos 1200 mm, soporte una puerta con bisagras de vidrio a vidrio o sea una mampara fija con un extremo libre.
El tubo de Φ22 mm se adapta a la mayoría de las duchas residenciales y de hoteles. Utilice Φ19 mm para barras cortas en paneles ligeros, y Φ25 mm para barras largas, vidrio de 12 mm o mamparas walk-in. También disponemos de tubos cuadrados y barras planas para diseños modernos y estilizados.
Fije el conector para vidrio cerca de la esquina superior del panel, normalmente de 50 a 100 mm por debajo del borde superior, para que la barra no interfiera con la apertura de la puerta. El orificio debe perforarse antes de templar el vidrio.
La mayoría de los conectores de barra de soporte HIPAD son compatibles con vidrio templado de 10–12 mm. Algunos conectores son aptos para vidrio de 6–12 mm. Indíquenos el grosor de su vidrio y le confirmaremos el conector adecuado.
Sí. Cuando no haya una pared lateral accesible, por ejemplo en una mampara walk-in, una barra vertical puede fijar el panel al techo. El techo debe contar con un punto de fijación sólido. Envíenos la altura del techo y las medidas del panel para confirmar la barra y los herrajes.
Las barras de soporte y los conectores HIPAD están fabricados en acero inoxidable 304 para ofrecer resistencia a la corrosión en baños húmedos. Es posible solicitar acero inoxidable 316 para proyectos en zonas costeras, piscinas y spas.
Sí. Las barras se fabrican según su plano de diseño, en acabados pulido, satinado, negro mate, dorado u otros recubrimientos galvánicos y PVD para combinar con sus bisagras y abrazaderas.
La cantidad mínima de pedido (MOQ) es de 1000 piezas. Las muestras tardan de 5 a 7 días y la producción, de 20 a 25 días laborables. Ofrecemos longitudes personalizadas, acabados, moldes propios, grabado o impresión de logotipos y embalaje personalizado; además, la personalización de logotipos y embalajes está disponible incluso para cantidades pequeñas.
HIPAD es un fabricante fundado en el año 2000 en Qingdao, China, que cuenta con matricería propia, más de 2000 juegos de moldes, producción y control de calidad. HIPAD cuenta con la certificación ISO 9001, y los productos aplicables disponen de las certificaciones CE, GS y CSA C-UL. Qingdao Hipad International Trade Co., Ltd. gestiona la exportación.
A hardware factory since 2000, supplying shower support bars and glass connectors to distributors, shower enclosure makers, glass processors and contractors in 60+ countries. Our commitment includes:
Tell us the layout, panel sizes, tube size, finish and quantity. We reply within 24 hours with drawings and a factory price list.
Responderemos en un plazo de 24 horas. Para solicitudes urgentes, contacte con nosotros por WhatsApp/WeChat en el +86 137 9191 8989 o llame directamente al mismo número.
*Respetamos la confidencialidad de sus datos y protegemos toda la información facilitada.
Solo utilizaremos sus datos para responder a su consulta y nunca enviaremos correos electrónicos no solicitados ni mensajes promocionales.
Kits de herrajes para puertas de ducha
Pinzas para vidrio
Bisagras para puertas de ducha
Glass Standoffs & Point Fixings