A shower support bar, also called a stabilizer bar, is a metal tube that ties the top of a fixed glass panel to a wall, the ceiling or another panel so the glass cannot flex. HIPAD makes support bars and their connectors in stainless steel 304: Φ19, Φ22 and Φ25 mm round tube, square tube and flat bars, with glass-to-wall and glass-to-glass connectors at 90°, 135° and 180° for 10–12 mm tempered glass. Distributors, shower enclosure makers and glass processors in 60+ countries buy them factory-direct, standard or custom.
A frameless shower panel is held only at its edges, by Pinces à verre or a U-channel. A tall panel with a free edge can still move at the top, and every time the door closes the panel takes the impact. A support bar fixes that top corner to a solid point, so the panel stays straight and the door keeps its alignment.
A support bar system has three parts: the tube or flat bar, un glass connector that clamps through a hole near the top of the panel, and a wall flange, ceiling fitting or second glass connector at the other end. The bar is also called a stabilizer bar, shower brace, header bar ou tie bar, and in Spanish barra estabilizadora, tirante para mampara ou barra de tracción para baño.
Representative models from the HIPAD range. Our catalog lists about 30 connector models for round and square tube. Every bar and connector can be made in your finish, length and packaging. Ask for the full catalog with drawings.
Réponse rapide : add a support bar when a fixed panel is wider than about 1000 mm, has a free vertical edge longer than about 1200 mm, ou carries a door on glass-to-glass hinges. Walk-in screens with one free end almost always need one. A panel clamped on two or three sides, under 1000 mm wide, usually does not.
| Situation | Support bar? | Typical bar |
|---|---|---|
| Panel clamped on wall and floor, up to 1000 × 2000 mm | Usually not | — |
| Panel 800–1000 mm wide next to a door | Recommended | Glass-to-wall, 90° |
| Panel wider than 1000 mm | Required | Glass-to-wall or wall-to-wall |
| Walk-in screen with a free end | Required | Glass-to-wall or glass-to-ceiling |
| Door hung on a fixed panel (glass-to-glass hinges) | Required | Glass-to-wall or header bar |
| Corner shower, door on the return panel | Recommended | Elbow or 90° corner bar |
| Panel taller than 2100 mm, or 12 mm glass | Required | Φ25 mm tube |
Send the panel sizes and the distance to the wall or ceiling. We return a bar length, tube size and connector list.
Choose a bar by what it connects: glass to a wall, glass to glass, or glass to the ceiling. The views below show each configuration seen from above, except the ceiling rod, which is shown from the front.
A straight tube from the top of the panel to the back or side wall, with a glass connector at one end and a wall flange at the other. Single-head and double-head versions are available.
Slanted-head, elbow and curved bars reach a wall point that is not square to the panel, or bend around a corner. Swivel connectors take up small angle differences on site.
Short bars and connectors that join a front panel to a return panel at 90°, or two panels to each other. They are used in corner showers where the door hangs on the return panel.
Flat bars and adjustable connectors link inline panels across a door opening (180°) or join the angled panels of a neo-angle shower (135°). They sit close to the glass for a slim look.
Vertical rods run from above down to the top of the panel. They are used for walk-in screens and islands where no side wall is within reach. Confirm the fixing details for your ceiling with us.
Tube clamps, wall flanges, end caps and custom connectors complete the system. We make connectors to your tube size, glass thickness and hole drawing, starting from our existing molds.
| Produit | Shower support bars (stabilizer bars), glass connectors, wall flanges and tube clamps for frameless shower enclosures and glass screens |
|---|---|
| Configurations | Glass-to-wall 90° and angled · glass-to-glass 90°, 135°, 180° · wall-to-wall · glass-to-ceiling |
| Bar types | Straight single-head and double-head, slanted-head, elbow, curved, 90° corner, 135° and 180° flat bars |
| Tube | Round Φ19, Φ22 and Φ25 mm · square tube · flat bar |
| Connector sizes | About 30 × 30 to 70 × 30 mm for standard connectors; larger bodies up to about 115 × 70 mm |
| Epaisseur du verre | 10–12 mm tempered glass; some connectors 6–12 mm |
| Longueur | Made to your layout drawing |
| Matériel | Acier inoxydable 304 |
| Finitions | Mirror polished, satin (brushed), matte black, gold; other plated and PVD colors to match your hinges and clamps |
| Joints | Rubber or PVC gaskets and sleeves at the glass connector |
| Quantité minimale de commande · échantillon · délai de livraison | 1 000 pièces · 5 à 7 jours · 20 à 25 jours ouvrés |
| Conditions commerciales | FOB Qingdao ou tout autre port chinois · Acompte de 30%, solde de 70% avant expédition · Virement bancaire (T/T), lettre de crédit (L/C), Western Union, PayPal · Garantie d'un an |
| Certifications | Système de gestion de la qualité ISO 9001 ; certifications CE, GS et CSA C-UL pour les produits concernés · Inspection par un organisme tiers (SGS / BV) disponible |
| Connector | Joins | Angle | Tube | Verre | Utilisation courante |
|---|---|---|---|---|---|
| Glass-to-wall connector + flange | Panel to wall | 90°, fixed | Φ19 / 22 / 25 mm | 10-12 mm | Standard shower screen |
| Swivel connector | Panel to wall | Réglable | Tube rond | 10-12 mm | Out-of-square walls, angled bars |
| Glass-to-glass bar connector | Panel to panel | 90° / 180° | Tube rond | 10-12 mm | Corner and inline enclosures |
| Adjustable glass-to-glass connector | Panel to panel | Réglable | Short tube | 10-12 mm | Neo-angle and custom angles |
| Flat bar clamp | Panel to panel | 135° / 180° | Flat bar | 10-12 mm | Slim inline and neo-angle screens |
| Square tube connector | Panel to wall or panel | 90° / 180° | Tube carré | 10-12 mm | Modern square hardware lines |
| Tube clamp | Tube to tube | — | Tube rond | — | Joining or supporting long bars |
| Barre de renfort | Extra clamps | U-channel | Full header | |
|---|---|---|---|---|
| What it stops | Top of the panel flexing | Edge movement | Edge movement along the full edge | Top movement of all panels |
| Works on a free edge? | Oui | No, needs a wall or floor | No, needs a wall or floor | Oui |
| Look | One slim tube | Minimal | Continuous line | Frame along the top |
| Préparation du verre | One hole per connector | Clamp-only or small holes | No drilling | Notches or holes |
| Idéal pour | Wide panels, walk-in screens, doors on glass | Panels under 1000 mm | Out-of-square walls | Large enclosures, sliding systems |
A support bar sits at the top of the shower, where steam collects and water does not dry quickly. HIPAD makes support bars and connectors in stainless steel 304, which resists rust in daily bathroom use far better than 201 or plated iron. For coastal, pool and spa projects, ask us about 316 stainless steel.
| Tube size | Look | Utilisation courante |
|---|---|---|
| Φ19 mm | Very slim | Short bars, light 8–10 mm panels |
| Φ22 mm | Norme | Most home and hotel showers |
| Φ25 mm | Strong | Long bars, 12 mm glass, walk-in screens |
| Square / flat | Modern, low profile | Square hardware lines, inline joints |
Support bars are made in the same finishes as our charnières de douche, glass clamps and handles, so the bar matches the rest of the enclosure. Other plated and PVD colors are available for private-label collections.
L'installation doit être effectuée par un vitrier qualifié.
| Problème | Corriger |
|---|---|
| Panel still moves with the bar fitted | Check the wall plugs hold; use a larger tube or move the connector closer to the top corner |
| Bar pulls the panel out of plumb | Measure the bar length after the panel is set; use a swivel or adjustable end |
| Door hits the bar | Move the connector lower or use an angled or elbow bar |
| Connector slips on the glass | Replace worn gaskets; tighten screws evenly |
| Rust spots on the bar | Use 304 stainless; clean with a neutral cleaner, not bleach |
HIPAD is a manufacturer, not a trading middleman. We started in 2000 with bearings and precision motion parts, and in 2020 we added stainless steel handles, glass clamps, shower fittings and railing. Tooling, molds, production, assembly and inspection are all in-house, so support bars and connectors can be built to your drawing, finish and brand.
Incoming materials, in-process parts and finished bars and connectors are inspected by our in-house QC team, including tube size, thread fit and surface finish. SGS or BV third-party inspection is available. HIPAD is ISO 9001 certifiés, et les produits concernés portent CE, GS et CSA C-UL certification. Les certificats relatifs à un modèle spécifique sont disponibles sur demande.
| 1. Demande de renseignements et plans | Send the layout, bar type, tube size, finish and quantity |
|---|---|
| 2. Échantillons | 5 à 7 jours |
| 3. Production | 20 à 25 jours ouvrés · Quantité minimale de commande : 1 000 pièces |
| 4. Expédition | FOB Qingdao ou tout autre port chinois |
| Terme | Signification | Également appelé |
|---|---|---|
| Barre de renfort | Tube that holds the top of a glass panel | Stabilizer bar, shower brace, tie bar, barra estabilizadora, tirante para mampara |
| Header bar | Bar running across the top of a door opening or enclosure | Top bar, header |
| Glass-to-wall connector | Fitting that clamps the bar to the glass | Glass bracket, bar clamp |
| Wall flange | Round plate that fixes the bar end to the wall | Wall bracket, escutcheon |
| Swivel connector | Connector with an adjustable angle | Adjustable connector, articulated joint |
| Elbow bar | Bar with a 90° bend for corners | Corner bar, tirante de codo |
| Flat bar | Flat strip joining panels at 135° or 180° | Strap connector |
Un panneau fixé au mur et au sol et d’une largeur inférieure à environ 1 000 mm n’en nécessite généralement pas. Ajoutez une barre de renfort lorsque le panneau est plus large qu’environ 1 000 mm, présente un bord vertical libre de plus d’environ 1 200 mm, supporte une porte sur des charnières verre-à-verre ou constitue une paroi de douche à l’italienne avec une extrémité libre.
Le Φ22 mm convient à la plupart des douches résidentielles et hôtelières. Utilisez le Φ19 mm pour les barres courtes sur des panneaux légers, et le Φ25 mm pour les barres longues, le verre de 12 mm ou les parois de douche à l’italienne. Des tubes carrés et des barres plates sont disponibles pour des designs modernes et épurés.
Fixez le raccord de verre près de l’angle supérieur du panneau, généralement à 50–100 mm sous le bord supérieur, afin que la barre ne gêne pas l’ouverture de la porte. Le trou doit être percé avant la trempe du verre.
La plupart des raccords de barres de renfort HIPAD conviennent au verre trempé de 10 à 12 mm. Certains raccords conviennent au verre de 6 à 12 mm. Indiquez-nous l’épaisseur de votre verre et nous confirmerons le raccord.
Oui. Lorsqu’aucun mur latéral n’est à portée, par exemple pour une paroi de douche à l’italienne, une tige verticale peut fixer le panneau au plafond. Le plafond doit disposer d’un point de fixation solide. Envoyez-nous la hauteur sous plafond et les dimensions du panneau afin de confirmer la tige et les fixations.
Les barres de renfort et raccords HIPAD sont fabriqués en acier inoxydable 304 pour résister à la corrosion dans les salles de bains humides. L’acier inoxydable 316 peut être envisagé pour les projets côtiers, de piscine et de spa.
Oui. Les barres sont fabriquées selon votre plan d’implantation, en finition polie, satinée, noir mat, dorée ou dans d’autres couleurs plaquées et PVD, afin de s’harmoniser avec vos charnières et vos pinces.
La quantité minimale de commande est de 1 000 pièces. Les échantillons nécessitent 5 à 7 jours et la production 20 à 25 jours ouvrables. Nous proposons des longueurs et finitions personnalisées, des moules privés, la gravure ou l’impression de logos ainsi que des emballages personnalisés ; la personnalisation du logo et de l’emballage est également disponible pour les petites quantités.
HIPAD est un fabricant fondé en 2000 à Qingdao, en Chine, disposant d’un outillage interne, de plus de 2 000 jeux de moules, ainsi que de capacités de production et de contrôle qualité. HIPAD est certifié ISO 9001, et les produits concernés bénéficient des certifications CE, GS et CSA C-UL. Qingdao Hipad International Trade Co., Ltd. gère les exportations.
A hardware factory since 2000, supplying shower support bars and glass connectors to distributors, shower enclosure makers, glass processors and contractors in 60+ countries. Our commitment includes:
Tell us the layout, panel sizes, tube size, finish and quantity. We reply within 24 hours with drawings and a factory price list.
Nous répondons sous 24 heures. Pour toute demande urgente, contactez-nous sur WhatsApp/WeChat au +86 137 9191 8989 ou appelez directement ce même numéro.
*Nous respectons la confidentialité de vos données et protégeons toutes les informations transmises.
Nous utiliserons vos informations uniquement pour répondre à votre demande et n'enverrons jamais d'e-mails non sollicités ni de messages promotionnels.
Kits de quincaillerie pour porte de douche
Pinces à verre
Charnières pour portes de douche
Glass Standoffs & Point Fixings