Glass Door Hardware Manufacturer & Supplier · China

Glass Door Hardware: Floor Springs, Door Closers, Patch Fittings, Pull Handles and Locks – A Buyer's Guide from the Factory

Glass door hardware is the set of fittings that hangs, controls, opens and locks a frameless tempered glass door: a floor spring or pivot with top and bottom patch fittings, a door closer where a floor spring cannot be used, pull handles, glass door locks and flush bolts. HIPAD makes floor springs for doors of 75–250 kg and up to 1500 × 2600 mm, door closers for 25–110 kg doors, patch fittings and stainless steel pull handles up to 1850 mm long. Glass processors, door contractors and distributors in 60+ countries buy complete door sets or single parts from our factory.

Floor springs 75–250 kg
Door closers 25–110 kg
Patch fittings · pivots
Pull handles 300–1850 mm
Glass door locks · flush bolts
10–12 mm tempered glass

Request Glass Door Hardware Catalog See the Parts of a Glass Door

HIPAD glass door hardware: floor springs, door closers, patch fittings and pivots

What Is Glass Door Hardware?

A frameless glass door is a single sheet of tempered glass with no frame. Because the glass cannot be screwed into, every fitting clamps onto it. The most common commercial set uses a floor spring set in the floor under the door: a bottom patch fitting on the lower corner of the glass sits on the floor spring spindle, and a top patch fitting turns on a top pivot in the transom or ceiling. A pull handle goes through holes in the glass, and a lock patch or floor lock secures the door.

Where the floor cannot be cut, a door closer or a concealed frameless closer does the closing instead. The same hardware is used on shop fronts, office entrances, hotel lobbies, glass partitions and bathroom doors. In Spanish the floor spring is a bisagra hidráulica de piso ou freno hidráulico, patch fittings are zapatas ou herrajes para puerta de vidrio templado, and the door closer is a cierrapuertas.

HIPAD Glass Door Hardware: Key Facts

Fabricant : HIPAD, Qingdao, Chine, fondée en 2000
Floor springs: 12 models, doors 75–250 kg and up to 1500 × 2600 mm, two-stage speed control
Door closers: 25–110 kg doors, surface and concealed, hold-open or non-hold-open
Frameless glass closer: 100 kg, door width up to 1000 mm, 8–13 mm glass, no floor cut
Patch fittings: top, bottom, L-corner and lock patches; 15 mm and 11.8 mm spindle inserts
Handles: SUS304 / SUS201 pull handles for 8–12 mm glass, 300–1850 mm
Commande : échantillons : 5 à 7 jours · production : 20 à 25 jours ouvrés · FOB Qingdao

Parts of a glass door

The Parts of a Frameless Glass Door

The drawing shows a single frameless glass door on a floor spring. Each numbered part links to the HIPAD range that supplies it.

Single frameless glass door on a floor spring. Not to scale.

#	Part	Job	HIPAD range
1	Top pivot	Upper pivot point, fixed in the transom or ceiling	Door controls
2	Top patch fitting	Clamps the top corner of the glass to the pivot	Patch fittings
3	Bottom patch fitting	Clamps the bottom corner and sits on the floor spring spindle	Patch fittings
4	Floor spring	Carries the door weight and closes it at a controlled speed	Floor springs
5	Pull handle	Back-to-back handle through holes in the glass	Glass door handles
6	Lock patch or glass door lock	Locks the door to the floor or the next leaf	Serrures
7	Flush bolt or door stop	Holds the second leaf of a double door; stops the swing	Verrous encastrés

Gammes de quincaillerie pour portes en verre HIPAD

Glass Door Hardware from Our Factory

Each range has its own page with models and specifications. Order a complete door set or single components.

Hydraulic floor spring with stainless steel cover plate

Control

Ressorts de plancher

Hydraulic floor springs for glass, timber and uPVC doors, 75–250 kg, two-stage speed control.

Surface-mounted hydraulic door closer with arm

Control

Ferme-portes

Surface and concealed closers for 25–110 kg doors, with or without 90° hold-open.

Stainless steel patch fittings for frameless glass doors

Fix glass

Patch Fittings & Pivots

Top, bottom, corner and lock patches with top pivots for floor spring glass doors.

Poignée de tirage pour porte en verre en acier inoxydable

Open

Poignées de porte en verre

SUS304 / SUS201 back-to-back pull handles for 8–12 mm glass, 300–1200 mm.

Stainless steel ladder pull handle for entrance doors

Open

Stainless Steel Entrance Handles

Heavy-duty commercial pulls 600–1500 mm for 35–70 mm doors, ladder, H-type and round tube.

Verrouiller

Glass Door & Door Locks

Center locks for single and double glass doors, mortise locks and cylinders.

Verrouiller

Verrous à encastrer

Standard, concealed and heavy-duty flush bolts, 150–400 mm, for the fixed leaf of double doors.

Fix glass

Glass Fittings & Connectors

Standoffs, point fixings and connectors for sidelights, fixed panels and canopies.

Step 1 · How the door closes

Floor Spring vs Door Closer vs Pivot vs Concealed Glass Door Closer

Réponse rapide : use a floor spring for heavy, busy frameless glass entrances where the floor can be cut; a surface door closer for framed, timber and steel doors; a pivot system for oversized or architectural doors; and a concealed frameless glass door closer when the floor cannot be cut and the glass door is up to 100 kg.

	Floor spring	Door closer	Pivot system	Concealed glass door closer
Where it sits	In a pocket in the floor	On the door face or frame head	Floor and head pivots	Inside the bottom patch, no floor pocket
HIPAD door weight	75–250 kg	25–110 kg	Large doors, up to about 200 kg	Up to 100 kg
Largeur de la porte	Up to 1500 mm	Up to about 1300 mm	Project-specific	Up to 1000 mm
Swing	Single or double action	Single action	Single or double action	150° each way
Look	Hidden; only a cover plate shows	Visible arm and body	Almost invisible	Hidden in the patch
Idéal pour	Shop fronts, malls, office entrances	Interior, fire and service doors	Feature entrances, villas	Renovations, bathrooms, offices

Step 2 · Floor spring size

How to Choose a Floor Spring by Door Weight and Size

Choose a floor spring whose maximum door weight et maximum leaf size both cover your door. Tempered glass weighs about 2,5 kg par m² par millimètre: a 1000 × 2400 mm door in 12 mm glass weighs about 72 kg before fittings, so a 100–120 kg floor spring leaves a safe margin.

All HIPAD floor springs have two-stage speed control: one valve for the closing swing, one for the final latching.
They suit single and double doors in glass, timber and uPVC.
Check the floor depth: floor spring boxes are about 42–70 mm deep.

HIPAD floor spring range: 12 models. Each model's exact ratings and box size are on its drawing.
Max door weight	Max door leaf (W × H)	Utilisation courante
75 kg	750 × 2100 mm	Light interior glass doors
95–100 kg	950–1000 × 2100–2200 mm	Office and bathroom glass doors
120–135 kg	1100–1200 × 2200–2500 mm	Shop fronts, hotel doors
150 kg	1200 × 2300–2400 mm	Busy commercial entrances
180–200 kg	1500 × 2200–2500 mm	Large entrance doors
250 kg	1500 × 2600 mm	Oversized and heavy doors

Step 3 · Door closer size

How to Choose a Door Closer

Door closers are sized by door weight and width. HIPAD surface closers cover doors from 25 to 110 kg in square, round and triangular bodies, and concealed closers cover 35–95 kg doors. Most models are available with or without 90° hold-open.

Finishes: brushed, titanium, red bronze, green bronze and black.
Door weight	Typical door width	HIPAD closer type
25–45 kg	Up to about 1000 mm	Compact square or round closer
45–65 kg	Up to about 1200 mm	Standard square or round closer
60–80 kg	Up to about 1300 mm	Large square or round closer
80–110 kg	Up to about 1000 × 2000 mm leaves	Heavy-duty triangular closer
35–95 kg	Up to about 1300 mm	Concealed closer

EN 1154 closer sizes (reference)

Many specifications in Europe and the Middle East call for closers by EN 1154 power size. Match the HIPAD model to the size the specification asks for.

EN size	Max door width	Door weight
EN 2	850 mm	Up to 40 kg
EN 3	950 mm	Jusqu'à 60 kg
EN 4	1100 mm	Jusqu'à 80 kg
EN 5	1250 mm	Up to 100 kg
EN 6	1400 mm	Jusqu'à 120 kg

No floor cut

Concealed Frameless Glass Door Closer

For renovations, offices and bathrooms where the floor cannot be opened, HIPAD supplies a frameless glass door closer built into the bottom fitting. It needs no floor pocket and no embedding work.

Door weight	Up to 100 kg
Largeur de la porte	Up to 1000 mm
Verre	8–13 mm tempered
Opening	150° each way; 90° hold-open optional
Speed	Closing zone 150°–10°, latching zone 10°–0°
Ajustement	Base ±3 mm front-back and side-to-side, ±4° rotation
Installation	No floor recess, no embedding

Fix the glass

Raccords de patch

Patch fittings clamp the corners of a frameless glass door and connect it to the floor spring and top pivot. A standard top or bottom patch measures about 164 × 51 × 32 mm.

Patch	Job
Bottom patch	Sits on the floor spring spindle
Top patch	Turns on the top pivot
L-corner patch	Joins a fixed sidelight and fanlight at the corner
Lock patch	Holds a floor lock or keeps for double doors

Spindle inserts are available for 15 mm and 11.8 mm floor spring spindles, which covers the most common floor springs on the market. Tell us which floor spring the door uses.

Step 4 · Handles and locks

Glass Door Handles, Locks and Flush Bolts

Round tube Φ25–38 mm or rectangular tube; chrome, satin, black and titanium black finishes.
Poignée	Porte	Longueur	Matériel
Back-to-back glass pull	Verre de 8 à 12 mm	300–1200 mm	SUS304 / SUS201
Heavy-duty entrance pull	35–70 mm doors	600–1500 mm	SUS304
Long pull with lock	Glass and entrance doors	Up to 1850 mm	Acier inoxydable
Sliding back-to-back pull	10–40 mm doors	200–800 mm	Acier inoxydable

Specify a pull handle by overall length, center-to-center hole distance, tube size, projection and glass thickness. See the back-to-back handle guide.

Lock or bolt	Use
Glass door center lock	Single or double glass doors, locks leaf to leaf
Lock patch / floor lock	Locks the bottom of the glass door to the floor
Mortise lock	Framed doors; brass, zinc alloy, iron or stainless bodies
Verrou à encastrer standard	Fixed leaf of interior double doors, 150–300 mm
Verrou encastré dissimulé	Hidden in the door edge, 200–350 mm
Verrou à encastrer renforcé	Commercial double doors, 250–400 mm

Ordering

Hardware List for a Frameless Glass Door

Typical list for a floor spring door. With a concealed glass door closer, replace the floor spring and bottom patch with the closer unit.
Part	Single door	Double door
Floor spring	1	2
Bottom patch	1	2
Top patch	1	2
Top pivot or transom patch	1	2
Pull handle (pair)	1	2
Lock patch, floor lock or center lock	1	1 center lock
L-corner patches (with sidelights and fanlight)	As needed	As needed

Glass and Finish

Use 10–12 mm tempered glass for entrance doors; 12 mm is standard for busy commercial doors.
All holes and notches for patches, handles and locks must be cut avant le revenu, to the hardware drawing.
Choose stainless steel covers and handles in one finish: chrome, satin, black or titanium black.
Near the sea or pools, specify SUS304 handles and stainless fixings.

Frameless glass entrance door with patch fittings

Glass Door Hardware by Application

Commercial Entrances

Floor springs, patch fittings, long pull handles and locks for shop fronts, malls and office lobbies.

Office & Interior Glass Doors

Patch fittings, concealed glass door closers and pull handles for meeting rooms and partitions.

Glass door with stainless steel pull handle

Bathroom & Residential Glass Doors

Pull handles, knobs and frameless closers for bathroom and residential glass doors.

Project references: shopping center glass doors, Los Angeles, USA, office glass door system, Singapore et apartment glass doors, Vancouver, Canada.

Présentation de l'installation

Confirm the door size, glass thickness and hardware set, and send the hardware drawing to the glass processor before tempering.
Set the floor spring box in the floor, level and in line with the top pivot; grout it in place.
Fix the top pivot in the transom or ceiling directly above the floor spring spindle.
Fit the patch fittings to the glass with their gaskets, then hang the door on the spindle and pivot.
Adjust the closing and latching speeds, then fit the handle, lock and cover plates.

Glass door hardware should be installed by a qualified glazier or door installer.

Common Problems and Fixes

Problème	Corriger
Door slams	Reduce the closing and latching speed on the valves
Door does not close fully	Increase the latching speed; check the door is plumb
Door sags or rubs	Check the top pivot is directly above the spindle; re-tighten patches
Oil on the cover plate	Floor spring seal failure; replace the unit
Handle loose on the glass	Replace the gaskets and re-tighten the through-bolts

Pourquoi acheter chez HIPAD ?

Glass Door Hardware from One Factory

HIPAD started in 2000 with bearings and precision motion parts and today supplies a complete door and glass hardware range. Floor springs, closers, patch fittings, handles and locks are produced and checked under one quality system, so a glass processor or contractor can source a complete door set in one finish from one supplier.

12floor spring models, 75–250 kg

25–110 kgdoor closer range

2000+kits de moules pour une personnalisation rapide

60+pays desservis

Contrôle qualité

Material and dimension checks of bodies, spindles, patches and handles
Closing and latching function checks on floor springs and closers
Fit checks of patches and handles on sample glass
Finish inspection and export packing checks

HIPAD est ISO 9001 certifiés, et les produits concernés portent CE, GS et CSA C-UL certification. SGS or BV third-party inspection is available.

OEM / ODM glass door hardware

Complete door sets matched in one finish
Handle lengths, hole centers and finishes to your drawing
Logo on cover plates and handles, private-label packing, même pour de petites quantités
Packing per door for projects, or bulk for distributors

1. Door schedule	Send door sizes, glass thickness, quantity and finish
2. Échantillons	5–7 days for existing models
3. Production	20 à 25 jours ouvrés
4. Expédition	FOB Qingdao ou tout port chinois · acompte de 30 %, 70 % avant expédition

Glass door guides

More Guides on Glass Door Hardware

Door Closer Weight Capacity and Opening AngleCloser, floor spring and pivot compared
Système de porte pivotante : guide du poids et de l’ouvertureLarge doors and structural checks
Back-to-Back Door Handles: Glass Door Spec GuideLength, centers and projection
Commercial Door Pull Handle: Dimensions GuideEntrance handle sizes and approvals
Glass Door Handle Supplier: B2B Buying GuideWhat to send for a correct quote
Verrou encastré dissimulé : guide des dimensions et des matériauxLengths, materials and fitting
Glass Hardware: B2B Supplier and Spec GuideDoor, sliding, clamp and railing hardware
Solutions d'entrée commercialeComplete entrance hardware approach

Glass Door Hardware Terms

Terme	Signification	Également appelé
Floor spring	Hydraulic closer set in the floor under a door	Floor hinge, floor closer, bisagra hidráulica de piso, freno hidráulico
Patch fitting	Clamp that fixes a hinge point to the corner of glass	Glass door patch, zapata
Top pivot	Upper pivot point of a floor spring door	Top centre, pivote superior
Double action	Door swings both ways	Double swing
Hold-open	Door stays open at a set angle	Dead stop, 90° stop
Latching speed	Speed over the last few degrees of closing	Latch zone
Flush bolt	Bolt in the edge of the fixed leaf of a double door	Edge bolt
Door closer	Surface or concealed device that closes a door	Cierrapuertas

Glass Door Hardware FAQ

Quelle quincaillerie est nécessaire pour une porte en verre sans cadre ?

Une porte en verre sans cadre avec ressort de sol nécessite un ressort de sol, une ferrure à pince inférieure, une ferrure à pince supérieure avec pivot supérieur, une poignée de tirage et une serrure à pince, une serrure de sol ou une serrure centrale. Les portes doubles nécessitent un ensemble pour chaque vantail et généralement une serrure centrale.

Quelle est la différence entre un ressort de sol et un ferme-porte ?

Un ressort de sol est encastré dans le sol sous la porte et en supporte le poids ; il convient donc aux lourdes portes en verre sans cadre et est presque invisible. Un ferme-porte est fixé sur la porte ou la traverse supérieure du cadre et sert uniquement à fermer la porte ; il convient donc aux portes à cadre, en bois et en acier.

Comment choisir la taille d'un ressort de sol ?

Choisissez un ressort de sol dont le poids maximal de porte et les dimensions maximales de vantail couvrent tous deux votre porte. Les ressorts de sol HIPAD vont de 75 kg pour des portes de 750 × 2100 mm à 250 kg pour des portes de 1500 × 2600 mm.

Une porte en verre peut-elle se fermer automatiquement sans découper le sol ?

Oui. Un ferme-porte dissimulé sans cadre en verre est intégré dans la ferrure inférieure et ne nécessite aucune réservation dans le sol. Le modèle HIPAD supporte des portes jusqu’à 100 kg et 1 000 mm de large, en verre de 8 à 13 mm, avec une ouverture de 150° dans chaque sens.

Quelle épaisseur de verre est utilisée pour les portes en verre ?

Les portes commerciales en verre sans cadre utilisent normalement du verre trempé de 10–12 mm, le 12 mm étant courant pour les entrées très fréquentées. Tous les trous et encoches doivent être réalisés avant la trempe du verre.

Quelles dimensions sont disponibles pour vos poignées de tirage de portes en verre ?

Les poignées de tirage dos à dos pour verre sont disponibles en longueurs de 300–1200 mm pour du verre de 8–12 mm, en SUS304 ou SUS201. Les poignées d'entrée robustes sont disponibles en 600–1500 mm pour des portes de 35–70 mm, ainsi que des longues poignées avec serrures jusqu'à 1850 mm.

Vos ferrures à pinces sont-elles compatibles avec nos ressorts de sol ?

Les ferrures à pinces HIPAD sont disponibles avec des inserts d'axe pour des axes de ressort de sol de 15 mm et 11,8 mm, ce qui couvre les ressorts de sol les plus courants. Indiquez-nous le modèle du ressort de sol et nous confirmerons l'insert.

Pouvez-vous fournir un ensemble complet de quincaillerie pour porte en verre ?

Oui. Nous fournissons des ressorts de sol, ferrures à pinces, pivots, poignées, serrures et verrous encastrés dans une même finition, emballés par porte pour les projets ou en vrac pour les distributeurs, avec emballage portant votre logo et sous marque privée disponible.

HIPAD est-il un fabricant ou une société de négoce ?

HIPAD est un fabricant fondé en 2000 à Qingdao, en Chine, qui produit des ferrures pour portes, fenêtres et vitrages avec ses propres moules et son propre contrôle qualité. HIPAD est certifié ISO 9001. Qingdao Hipad International Trade Co., Ltd. gère les exportations.

Dernière mise à jour : octobre 2026 · Relu par Allen, ingénieur technique, HIPAD

Related Hardware

Quincaillerie pour portes coulissantes

Quincaillerie pour garde-corps en verre

Pinces à verre Stainless steel door hinges

Charnières de porte

Send Your Glass Door Hardware Requirements To HIPAD

Pourquoi nous choisir ?

A door and glass hardware factory since 2000, supplying glass processors, door contractors, distributors and developers in 60+ countries. Our commitment includes:

Certification ISO 9001 ; marquages CE, GS et CSA C-UL pour les produits concernés ; inspections SGS / BV disponibles
Floor springs, closers, patch fittings, handles and locks from one factory, in one finish
Échantillons sous 5 à 7 jours, production en série sous 20 à 25 jours ouvrés
OEM / ODM: lengths, finishes, logo and per-door packing, even for small quantities

Send your door sizes, glass thickness, quantity and finish. We reply within 24 hours with a hardware list and a factory price.

Demander un devis

Obtenir un devis

Nous répondons sous 24 heures. Pour toute demande urgente, contactez-nous sur WhatsApp/WeChat au +86 137 9191 8989 ou appelez directement ce même numéro.

*Nous respectons la confidentialité de vos données et protégeons toutes les informations transmises.

Nous utiliserons vos informations uniquement pour répondre à votre demande et n'enverrons jamais d'e-mails non sollicités ni de messages promotionnels.